=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.19 13:14:16 =~=~=~=~=~=~=~=~=~=~=~= Fastboot 3.2.2-svn8 (Oct 10 2013 - 18:28:20) Fastboot: Version 3.2.2 0x1 Machine ID: 8000 v0 Build Date Oct 7 2013, 16:00:07 Serial Number: godbox CPU: Hi3716Mv300 Boot Media: NAND Check nand flash controller v301. Check nand flash controller v504. found Special Nand id table Version 1.36 Nand ID: 0xAD 0xD5 0x94 0x9A 0x74 0x42 0xAD 0xD5 Nand(Auto): Block:2MB Page:8KB Chip:2GB*1 OOB:368B ECC:24bits/1K gpio_write_bit,178: para u32GpioPathNum is invalid. In: serial Out: serial Err: serial silent boot mode Press Ctrl+C to stop autoboot market id=0x08,0x02,0x00,0x01 gpio_write_bit,178: para u32GpioPathNum is invalid. nand_read_loaderinfo:0x400000 [ff,ff,ff,ff] gpio_init,298: init hi_gpio success. front button=1,1,1 NAND read: device 0 offset 0x3400000, size 0xa00000 10485760 bytes read: OK NAND read: device 0 offset 0x4800000, size 0x7800000 125829120 bytes read: OK [RSA_AES_2] Verifying signature 82000000 at 829fff00 --> Success! Decrypting 82000000 size 00a00000 --> Success! Verifying main signature 88000000 size 07800000 --> Success! ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-2.6.35.7_hisilicon Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3913080 Bytes = 3.7 MiB Load Address: 80800000 Entry Point: 80800000 Verifying Checksum ... OK Loading Kernel Image ... OK OK silent boot mode Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.35.7_hisilicon (jenkins_CME_OTT@laura) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #1 Mon Mar 3 10:43:34 CET 2014 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: godbox Memory policy: ECC disabled, Data cache writeback CPU:Hi3716Mv300, Timer:100M Built 1 zonelists in Zone order, mobility grouping on. Total pages: 79248 Kernel command line: mem=312M console=ttyAMA0,115200 mmz=ddr,0,0x93800000,200M DmxPoolBufSize=0x200000 mtdparts=hinand:2M(boot),2M(bootargs),2M(loaderparam),2M(stbconfig),2M(baseparam),2M(logo),20M(loader),20M(loader2),20M(kernel),200M(main),500M(data),64M(fastplay),-(reserved) rootfstype=jffs2 root=/dev/mtdblock9 ro MuteCtl_GPIO=0x1A1 silent_boot 000000------setup_zones=ddr,0,0x93800000,200M------000000 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 312MB = 312MB total Memory: 304612k/304612k available, 14876k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xd4000000 - 0xfe000000 ( 672 MB) lowmem : 0xc0000000 - 0xd3800000 ( 312 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0023000 ( 108 kB) .text : 0xc0023000 - 0xc06e7000 (6928 kB) .data : 0xc070c000 - 0xc075c640 ( 322 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Calibrating delay loop... 1205.86 BogoMIPS (lpj=6029312) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok fastplay_init,172: >>>>>> fastplay begin >>>>>> !!! Module himedia: init ok Hisilicon Media Memory Zone Manager state 0 mce_env_init,335: mmz_info_partion checkflag error!!! fastplay_Param_Init,1047: mce_env_init err fastplay_init,179: fastplay Param Init err !Load pre hi_gpio.ko success. (SDK_VERSION:[SDK_VERSION] Build Time:[Jan 8 2014, 11:49:06]) task_led_deamon,118: >>>>>> LED blinker begin >>>>>> fastplay_init,213: <<<<<< fastplay(mem=312M console=ttyAMA0,115200 mmz=ddr,0,0x93800000,200M DmxPoolBufSize=0x200000 mtdparts=hinand:2M(boot),2M(bootargs),2M(loaderparam),2M(stbconfig),2M(baseparam),2M(logo),20M(loader),20M(loader2),20M(kernel),200M(main),500M(data),64M(fastplay),-(reserved) rootfstype=jffs2 root=/dev/mtdblock9 ro MuteCtl_GPIO=0x1A1 silent_boot) disabled <<<<<< NET: Registered protocol family 16 Serial: AMBA PL011 UART driver uart:0: ttyAMA0 at MMIO 0x101fb000 (irq = 59) is a AMBA/PL011 console [ttyAMA0] enabled bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Advanced Linux Sound Architecture Driver Version 1.0.23. Switching to clocksource timer1 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. L2cache cache controller enabled VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NTFS driver 2.1.29 [Flags: R/O]. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.14) msgmni has been set to 594 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered loop: module loaded mtdoops: mtd device (mtddev=name/number) must be supplied physmap platform flash device: 02000000 at 34000000 physmap-flash physmap-flash.0: map_probe failed Check Spi Flash Controller V300. Check Spi Flash Controller V350. Found Special NAND id able Version 1.36 Check Nand Flash Controller V301. Check Nand Flash Controller V504. Found Nand ID: 0xAD 0xD5 0x94 0x9A 0x74 0x42 0xAD 0xD5 Nand: Hynix H27UAG8T2B Nand(Hardware): Block:2MB Page:8KB OOB:448B ECC:24bits/1K Chip:2GB*1 13 cmdlinepart partitions found on MTD device hinand Creating 13 MTD partitions on "hinand": 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000400000 : "bootargs" 0x000000400000-0x000000600000 : "loaderparam" 0x000000600000-0x000000800000 : "stbconfig" 0x000000800000-0x000000a00000 : "baseparam" 0x000000a00000-0x000000c00000 : "logo" 0x000000c00000-0x000002000000 : "loader" 0x000002000000-0x000003400000 : "loader2" 0x000003400000-0x000004800000 : "kernel" 0x000004800000-0x000011000000 : "main" 0x000011000000-0x000030400000 : "data" 0x000030400000-0x000034400000 : "fastplay" 0x000034400000-0x000080000000 : "reserved" Fixed MDIO Bus: probed himii: probed Up port phy at 0x01 is connect PHY himii:03 not found hieth:hieth_platdev_probe_port:543: connect to phy_device himii:03 failed! ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver hiusb-ehci hiusb-ehci.0: HIUSB EHCI hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1 hiusb-ehci hiusb-ehci.0: irq 96, io mem 0x60080000 hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver hiusb-ohci hiusb-ohci.0: HIUSB OHCI hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2 hiusb-ohci hiusb-ohci.0: irq 97, io mem 0x60070000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver cdc_wdm Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for debug usbcore: registered new interface driver debug USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems mice: PS/2 mouse device common for all mice usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio usbcore: registered new interface driver snd-usb-caiaq ALSA device list: No soundcards found. GACT probability on Mirror/redirect action on Simple TC action Loaded Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (4759 buckets, 19036 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 17 Bridge firewalling registered Ebtables v2.0 registered lib80211: common routines for IEEE802.11 drivers VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) usb 1-1: new high speed USB device using hiusb-ehci and address 2 usb 1-2: new high speed USB device using hiusb-ehci and address 3 hub 1-2:1.0: USB hub found hub 1-2:1.0: 2 ports detected VFS: Mounted root (jffs2 filesystem) readonly on device 31:9. Freeing init memory: 108K yaffs: dev is 32505866 name is "mtdblock10" rw yaffs: passed flags "" rtusb init rt2870 ---> === pAd = d42c9000, size = 510192 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 usbcore: registered new interface driver rt2870 Hisilicon Media Memory Zone Manager stage 1 Load hi_common.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:52:33]) Load hi_gpio.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:29]) Load hi_gpioi2c.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:30]) Load hi_i2c.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:39]) Load tde.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Mar 3 2014, 10:45:46]) Load hi_otp.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Dec 5 2012, 21:34:30]) Load hi_mpi.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:52:36]) Load hi_svdec.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Dec 5 2012, 22:03:47]) Load hi_tuner.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:31]) Load hi_sci.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:44]) Load hi_ir.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:34]) Load hi_cipher.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:50]) Load hi_advca.ko success. (SDK_VERSION:[X5HDV100R001C00] Build Time:[Jul 28 2012, 15:05:56]) Load hi_e2prom.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:40]) input: keyled_key as /devices/virtual/input/input0 Load hi_keyled.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Jan 8 2014, 11:53:41]) Load jpeg6b.ko success. (SDK_VERSION:[jpeg6bv1.0] Build Time:[Mar 3 2014, 10:45:47]) success to create the proc graphics/jpeg ! Load png.ko success. (SDK_VERSION:[Hi3716XV100R001C00SPC0A1] Build Time:[Mar 3 2014, 10:46:50]) fastplay_end,1263: play_Info->PlayTime = 0 play_time,1254: play time = 42949394 [22232 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22239 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22245 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22250 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [22258 ERROR-hdmi]:SI_TimerHandler[471]:Read EDID times:1 [22304 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22312 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22318 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22323 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [22331 ERROR-hdmi]:SI_TimerHandler[471]:Read EDID times:2 [22377 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22384 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22390 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22395 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [2243 ERROR-hdmi]:SI_TimerHandler[471]:Read EDID times:3 [22450 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22457 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22463 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22468 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [22476 ERROR-hdmi]:SI_TimerHandler[471]:Read EDID times:4 [22522 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22529 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22535 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22540 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [22548 ERROR-hdmi]:SI_TimerHandler[471]:Read EDID times:5 [22594 ERROR-hdmi]:SI_BlockReadMDDCFifo[194]:Read MDDC_FIFO_ERR read 0/16 Byte. [22602 ERROR-hdmi]:SI_BlockRead_MDDC[276]:SI_BlockReadMDDCFifo error [22608 ERROR-hdmi]:SI_PrepareEDID[1946]:Can NOT read EDID. [22613 ERROR-hdmi]:SI_EDIDProcessing[418]:come to here force setting Force to HDMI Mode [22621 ERROR-hdmi]:SI_TimerHandler[468]:Read EDID times:6 [22627 ERROR-hdmi]:SI_GetHdmiSinkCaps[2483]:EIDI Parse Error, Need to force setting Force to HDMI Mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode task_led_deamon,142: >>>>>> LED blinker end >>>>>> HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode HDCP AUTO Check RI Sink is in standy mode (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc] RTMP_TimerListAdd: add timer obj d43109c8! RTMP_TimerListAdd: add timer obj d43109f8! RTMP_TimerListAdd: add timer obj d4310a28! RTMP_TimerListAdd: add timer obj d4310998! RTMP_TimerListAdd: add timer obj d4310908! RTMP_TimerListAdd: add timer obj d4310938! RTMP_TimerListAdd: add timer obj d42db53c! RTMP_TimerListAdd: add timer obj d42cad40! RTMP_TimerListAdd: add timer obj d42cad78! RTMP_TimerListAdd: add timer obj d42db5e0! RTMP_TimerListAdd: add timer obj d42db4dc! RTMP_TimerListAdd: add timer obj d42db5ac! -->RTUSBVenderReset <--RTUSBVenderReset Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 5 2. Phy Mode = 5 NVM is Efuse and its size =2d[2d0-2fc] phy mode> Error! The chip does not support 5G band 15! RTMPSetPhyMode: channel is out of range, use first channel=1 (Efuse for 3062/3562/3572) Size=0x2d [2d0-2fc] 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 AsicSetRxAnt, switch to main antenna MCS Set = ff 00 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 PM: Syncing filesystems ... done. Freezing user space processes ... (elapsed 0.01 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done. ==============Png suspend! ===================jpge suspend! jpeg suspend ok. [1566941821 FATAL-ecs]:keyled_pm_suspend[620]:keyled_pm_suspend ok [1566941827 FATAL-ecs]:e2prom_suspend[424]:e2prom_suspend ok [1566941833 FATAL-Invalid]:ca_pm_suspend[110]:ok! [1566941838 FATAL-ecs]:cipher_pm_suspend[704]:ok ! [1566941842 FATAL-ecs]:sci_pm_suspend[736]:sci_pm_suspend ok === hifb_suspend start === === hifb_suspend ok === [1566941852 FATAL-tuner]:tuner_suspend[1790]:ok ! [1566941857 FATAL-hdmi]:hdmi_Suspend[452]:HDMI Suspend [1566941923 FATAL-hdmi]:hdmi_Suspend[489]:finish HDMI Suspend [1566941928 FATAL-vp]:VP_Suspend[629]:VP suspend OK. [1566941933 FATAL-sync]:SYNC_Suspend[502]:SYNC suspend OK. [1566941938 FATAL-pvr]:pvr_pm_suspend[510]:ok [1566941961 FATAL-vdec]:vdec_pm_suspend[6151]:ok [1566941966 FATAL-aenc]:aenc_pm_suspend[368]:ok [1566941970 FATAL-adec]:adec_pm_suspend[516]:ok [1566941974 FATAL-Invalid]:ao_pm_suspend[1223]:ok [1566941979 ERROR-Invalid]:ai_pm_suspend[922]:ai_pm_suspend line[922] [1566941985 FATAL-Invalid]:ai_pm_suspend[927]:ok [1566941992 FATAL-ao]:HIAO_DRV_Suspend[3116]:ok ! [1566941996 FATAL-avplay]:AVPLAY_Suspend[779]:AVPLAY suspend OK. [1566942061 FATAL-vo]:VO_Suspend[1345]:VO suspend OK. [1566942121 FATAL-disp]:DISP_Suspend[1024]:DISP suspend OK. [1566942127 FATAL-venc]:VENC_DRV_Suspend[204]:entering VENC_DRV_Suspend [1566942133 FATAL-vi]:vi_pm_suspend[489]:entering vi_pm_suspend [1566942139 FATAL-ecs]:otp_pm_suspend[220]:otp_pm_suspend ok ===================tde suspend! [1566942147 FATAL-ecs]:i2c_pm_suspend[560]:i2c_pm_suspend ok Bulk In Failed. Status=-2, BIIdx=0x2, BIRIdx=0x2, actual_length= 0x0